Skip to content

Pegboard Camera Wall

3D print files for camera holders that hang on an IKEA SKADIS pegboard. The two organizers come in a charging version, where the camera charges when you set it down, and in a version without charging.

This is a digital download of 3D print files. You print the parts yourself. Nothing is shipped.

Staging preview. The checkout links are not set yet, so the Buy buttons go nowhere.

The charging cable link on this page is a paid Amazon link. As an Amazon Associate I earn from qualifying purchases.

I built this set for my own camera wall. I wanted every camera to have its own spot on the pegboard, and I wanted my Osmo Pocket and my Luna Ultra to charge the moment I set them down.

So I measured each camera with calipers, printed test pieces until the fit was right, and shaped the holders to hang flush in one row. Both charging organizers are printed and working on my own wall.

These are the designs I print for myself. You get the files, a short guide, and a small test piece that makes sure the hooks fit your board before you spend hours on a print.

The print files

Five holders, each its own download, and a complete set with all five.

Pocket Cam Organizer by Video Hook, rendering on a pegboard

Pocket Cam Organizer by Video Hook

For DJI Osmo Pocket 3 and Osmo Pocket 4P.

Three pockets for your Osmo Pocket cameras on the pegboard. In the charging version, set a camera down and it charges.

  • With charging and without, both in the download.
Pocket Cam Organizer in two versions, side by side. With charging: a USB-C plug in the floor of each pocket. Without charging: a plain hole in the floor of each pocket.
Both versions are in the download: with charging and without.

Charging needs one exact USB-C cable for each camera that charges. The cable is not included.

9 USD
Buy the Pocket Cam Organizer

By buying you agree to the Terms and Conditions, the Refund Policy and the 3D print file license.

Details: the download, what you need, print times

In the download

  • The START-HERE guide and the license.
  • Test pieces: the hook fit test, the camera fit gauge and the charging test.
  • The organizer with hook fit 1, 2 and 3, each with charging and without.
  • Three numbered slide-in keys and an optional cord clip for the three cords.
  • Every part as a Bambu Studio .3mf, already sliced for the Bambu Lab X1 Carbon, and as a plain .stl for any other printer or slicer.

What you need

  • A 3D printer with a bed of 180 x 180 mm or larger, and PLA filament.
  • An IKEA SKADIS pegboard.
  • For the charging version only: one cable for each camera that charges, up to three. Not included, you buy it separately. The only cable I have tested: LEIRUI Down Angle USB-C, 3.3 ft / 1 m, silicone, the USB 20Gbps version. The link is further down this page, under What you need for the charging versions.
  • For the charging version: a certified USB-C charger with one port for each cable.
  • The version without charging needs no cable.

Print time and filament (slicer estimates for the Bambu Lab X1 Carbon)

  • Charging organizer: about 2 h 50 min, 65 g.
  • Organizer without charging: about 2 h 20 min, 56 g.
  • Hook fit test: about 50 min, 17 g, for all three pieces.
  • Camera fit gauge: about 20 min, 7 g.
  • Charging test: about 1 h 10 min, 19 g.
  • Slide-in keys: about 30 min, 5 g, for a plate of three.
  • Cord clip (optional): about 25 min, 7 g.

Good to know

  • The organizer is 119.7 mm wide and 56 mm tall. Front to back with the hooks it is about 72 mm with charging and about 62 mm without.
  • In a row with the other parts the sides sit flush. The version without charging is shallower, so its front sits 10 mm further back than theirs.
  • The pockets are cut for the bare camera handle, not for a case or a cage. The regular Osmo Pocket 4 has not been tested. Print the camera fit gauge first.
  • How it was tested: the pocket size was checked with a printed fit gauge on both of my cameras, a Pocket 3 and a Pocket 4P. The charging organizer is printed in full and in daily use on my own wall with the Pocket 4P.

Charging versions: read what you need and the safety note.

Luna Cam Organizer by Video Hook, rendering on a pegboard

Luna Cam Organizer by Video Hook

For Insta360 Luna Ultra, with its protective cover on.

A pegboard home for the Insta360 Luna Ultra and its attachments. In the charging version, set the camera down and it charges.

  • With charging and without, both in the download.
Luna Cam Organizer in two versions, side by side. With charging: a USB-C plug in the floor of the left pocket. Without charging: a plain hole in the floor of the left pocket.
Both versions are in the download: with charging and without.

Charging needs one exact USB-C cable. The cable is not included.

9 USD
Buy the Luna Cam Organizer

By buying you agree to the Terms and Conditions, the Refund Policy and the 3D print file license.

Details: the download, what you need, print times

In the download

  • The START-HERE guide and the license.
  • Test pieces: the hook fit test, the camera fit gauge and the charging test.
  • The organizer with hook fit 1, 2 and 3, each with charging and without.
  • Three numbered slide-in keys. This organizer uses one.
  • Every part as a Bambu Studio .3mf, already sliced for the Bambu Lab X1 Carbon, and as a plain .stl for any other printer or slicer.

What you need

  • A 3D printer with a bed of 180 x 180 mm or larger, and PLA filament.
  • An IKEA SKADIS pegboard.
  • For the charging version only: one cable. Not included, you buy it separately. The only cable I have tested: LEIRUI Down Angle USB-C, 3.3 ft / 1 m, silicone, the USB 20Gbps version. The link is further down this page, under What you need for the charging versions.
  • For the charging version: a certified USB-C charger with one free port.
  • The version without charging needs no cable.

Print time and filament (slicer estimates for the Bambu Lab X1 Carbon)

  • Charging organizer: about 2 h 55 min, 68 g.
  • Organizer without charging: about 2 h 30 min, 61 g.
  • Hook fit test: about 50 min, 17 g, for all three pieces.
  • Camera fit gauge: about 25 min, 10 g.
  • Charging test: about 1 h 20 min, 24 g.
  • Slide-in keys: about 30 min, 5 g, for a plate of three.

Good to know

  • The organizer is 119.7 mm wide and 56 mm tall. Front to back with the hooks it is about 80 mm with charging and about 72 mm without.
  • In a row with the other parts the sides sit flush. The charging version is deeper, so its front stands about 9 mm in front of theirs.
  • The left pocket holds the Luna Ultra with its protective cover on, and it is the pocket that charges in the charging version. The other two pockets store the 1/4 inch thread attachment or the battery handle.
  • How it was tested: every pocket is cut from caliper readings of my own camera and attachments. The charging organizer is printed in full and working on my own wall.

Charging versions: read what you need and the safety note.

Action Cam Holder by Video Hook, rendering on a pegboard

Action Cam Holder by Video Hook

For DJI Osmo Action 5 Pro, in its DJI protective frame.

Your Osmo Action 5 Pro in its frame and three spare batteries, upright on the pegboard and easy to grab.

  • Three angled slots for spare batteries. No charging.
5 USD
Buy the Action Cam Holder

By buying you agree to the Terms and Conditions, the Refund Policy and the 3D print file license.

Details: the download, what you need, print times

In the download

  • The START-HERE guide and the license.
  • Test pieces: the hook fit test and the camera fit gauge.
  • The holder with hook fit 1, 2 and 3.
  • Every part as a Bambu Studio .3mf, already sliced for the Bambu Lab X1 Carbon, and as a plain .stl for any other printer or slicer.

What you need

  • A 3D printer with a bed of 180 x 180 mm or larger, and PLA filament.
  • An IKEA SKADIS pegboard.

Print time and filament (slicer estimates for the Bambu Lab X1 Carbon)

  • Holder: about 3 h 15 min, 80 g.
  • Hook fit test: about 50 min, 17 g, for all three pieces.
  • Camera fit gauge: about 30 min, 15 g.

Good to know

  • The holder is 159.7 mm wide, 56 mm tall and about 72 mm front to back with the hooks.
  • The battery slots are for the DJI Osmo Action Extreme Battery Plus. The older 1770 mAh battery has the same shell. I have only tested the Osmo Action 5 Pro in its DJI protective frame.
  • How it was tested: the camera pocket and the battery slots were checked with a printed fit gauge, using my own camera in its frame and my own batteries.
Ace Cam Holder by Video Hook, rendering on a pegboard

Ace Cam Holder by Video Hook

For Insta360 Ace Pro 2, without a case.

Your Insta360 Ace Pro 2 and three spare batteries, upright on the pegboard with the lens clear of plastic.

  • Three angled slots for spare batteries. No charging.
5 USD
Buy the Ace Cam Holder

By buying you agree to the Terms and Conditions, the Refund Policy and the 3D print file license.

Details: the download, what you need, print times

In the download

  • The START-HERE guide and the license.
  • Test pieces: the hook fit test and the camera fit gauge.
  • The holder with hook fit 1, 2 and 3.
  • Every part as a Bambu Studio .3mf, already sliced for the Bambu Lab X1 Carbon, and as a plain .stl for any other printer or slicer.

What you need

  • A 3D printer with a bed of 180 x 180 mm or larger, and PLA filament.
  • An IKEA SKADIS pegboard.

Print time and filament (slicer estimates for the Bambu Lab X1 Carbon)

  • Holder: about 3 h 15 min, 80 g.
  • Hook fit test: about 50 min, 17 g, for all three pieces.
  • Camera fit gauge: about 35 min, 15 g.

Good to know

  • The holder is 159.7 mm wide, 56 mm tall and about 72 mm front to back with the hooks.
  • The battery slots are for the Ace Pro 2 battery. I have only tested the Ace Pro 2.
  • How it was tested: the camera pocket and the battery slots were checked with printed fit gauges, using my own camera and batteries. The pocket was reworked twice along the way, for the wind guard and for the screen buttons, and the final gauge passed.
360 Cam Holder by Video Hook, rendering on a pegboard

360 Cam Holder by Video Hook

For Insta360 X6 in its soft pouch and X5 with its lens cap on.

Two 360 cameras, two spare batteries and three microSD cards in one holder on the pegboard.

  • Needs a print bed at least 220 mm wide.
  • No charging.
5 USD
Buy the 360 Cam Holder

By buying you agree to the Terms and Conditions, the Refund Policy and the 3D print file license.

Details: the download, what you need, print times

In the download

  • The START-HERE guide and the license.
  • Test pieces: the hook fit test, the camera fit gauge and a microSD card slot test.
  • The holder with hook fit 1, 2 and 3.
  • Every part as a Bambu Studio .3mf, already sliced for the Bambu Lab X1 Carbon, and as a plain .stl for any other printer or slicer.

What you need

  • A 3D printer with a bed at least 220 mm wide, and PLA filament. The holder and its fit gauge are 199.7 mm wide. They do not fit a 180 x 180 mm bed.
  • An IKEA SKADIS pegboard.

Print time and filament (slicer estimates for the Bambu Lab X1 Carbon)

  • Holder: about 4 h, 98 g.
  • Hook fit test: about 50 min, 17 g, for all three pieces.
  • Camera fit gauge plate: about 50 min, 23 g.

Good to know

  • The holder is 199.7 mm wide, 56 mm tall and about 72 mm front to back with the hooks.
  • I have only tested the X5 and the X6. For anything else, print the camera fit gauge first.
  • How it was tested: both camera pockets and the battery slot were cut from caliper readings of my own gear and checked with a printed fit gauge.
Pegboard Camera Wall, complete set, rendering on a pegboard

Pegboard Camera Wall, complete set

All five of the above.

All five camera holders in one download. Build the whole camera wall, with or without charging.

  • Both versions of each organizer, with charging and without, are in the download.

The charging versions need one exact USB-C cable for each camera that charges. Cables are not included.

19 USD

Bought one by one, the five add up to 33 USD.

Buy the complete set

By buying you agree to the Terms and Conditions, the Refund Policy and the 3D print file license.

Details: the download, what you need, print times

In the download

  • The START-HERE guide for the whole set and the license.
  • Every test piece: the hook fit test, the five camera fit gauges, the microSD card slot test and both charging tests.
  • Every part with hook fit 1, 2 and 3: the three holders, and both organizers with charging and without.
  • Three numbered slide-in keys and the optional cord clip for the Pocket Cam Organizer.
  • Every part as a Bambu Studio .3mf, already sliced for the Bambu Lab X1 Carbon, and as a plain .stl for any other printer or slicer.

What you need

  • A 3D printer and PLA filament. Four of the five parts fit a bed of 180 x 180 mm. The 360 Cam Holder and its fit gauge are 199.7 mm wide and need a bed at least 220 mm wide.
  • An IKEA SKADIS pegboard. All five parts in one row need about 760 mm of board width. They also work split over two rows.
  • For the charging version only: one cable for each camera that charges, up to four. Not included, you buy it separately. The only cable I have tested: LEIRUI Down Angle USB-C, 3.3 ft / 1 m, silicone, the USB 20Gbps version. The link is further down this page, under What you need for the charging versions.
  • For the charging version: a certified USB-C charger with one port for each cable.
  • The version without charging needs no cable.

Print time and filament (slicer estimates for the Bambu Lab X1 Carbon)

  • The five main parts with both charging versions add up to about 16 hours and about 390 g.
  • Hook fit test: about 50 min, 17 g, for all three pieces. You print it once for the whole set.
  • Camera fit gauges: about 20 to 50 min and 7 to 23 g each.
  • Charging tests: about 1 h 10 min, 19 g for the Pocket Cam Organizer and about 1 h 20 min, 24 g for the Luna Cam Organizer.

Good to know

  • You do not have to print all five. Each part hangs on its own, and any two sit flush side by side.
  • In a row the sides sit flush, but the fronts step where depths differ. The Luna Cam Organizer with charging stands about 9 mm in front of the other parts, and the Pocket Cam Organizer without charging sits 10 mm further back.
  • One hook fit test covers the whole wall. All five parts use the same hook, so the same number works for all of them.
  • Each part is described on its own card above, with how it was tested.

Charging versions: read what you need and the safety note.

The pictures are renderings of the print files.

Before you buy

Personal license for one buyer: print as many as you need for yourself and as gifts, and change the files for your own use. Do not share, resell or re-upload the files or changed versions, and do not sell prints without a commercial license (email oleg@olegkovalov.com to ask).

Read the full license: 3D print file license

Digital files are delivered instantly, so all sales are final once you download. If a file is faulty or not as described, email me within 14 days of purchase and I will fix it or refund you. Print the small test pieces in the download first, before any full part. Full refund policy

Buyers in the EU, EEA and UK: by buying you ask for the download to start right away, and you agree that you lose your 14-day right to cancel once the download begins. Your rights if a file is faulty or not as described stay the same.

Sliced for the Bambu Lab X1 Carbon. STL files included for other printers.

The 360 Cam Holder is 199.7 mm wide. It needs a print bed at least 220 mm wide and does not fit a 180 x 180 mm bed.

Independent design by Video Hook LLC, not made, authorized, sponsored or approved by IKEA, DJI or Insta360; brand and product names belong to their owners and are used only to describe fit.

How it works

1. Print the test

Pegboards differ in thickness. Print the small hook fit test first, about 50 minutes on my printer for three numbered pieces. Hang them on your board and note the number that sits snug with no rattle.

2. Print the part

Open the folder with your number and print the part. The files are sliced for the Bambu Lab X1 Carbon, and a plain .stl is included for any other printer. For the charging versions, lay the cable in and slide in the printed key until it clicks.

3. Hang it

Push the hooks into the board, press the part flat and let it drop into place. The holders sit side by side, in any order, with a 0.30 mm seam.

What makes this set different

  • The camera charges when you set it down. In the two charging organizers a USB-C plug waits in the pocket floor.
  • Every part is 56 mm tall and hangs flush next to the others.
  • The hooks come in three fits. A small test print shows which one hangs snug on your board.
  • The pockets are cut for real setups: the Action 5 Pro in its frame, the Luna Ultra with its cover on, the X6 in its pouch.

What you need for the charging versions

  • An IKEA SKADIS pegboard.
  • A 3D printer and PLA filament. Tested on Bambu Lab X1 Carbon with PLA Matte.
  • One charging cable for each camera that charges. The plug bay is cut for one exact plug, and this is the only cable I have tested: LEIRUI Down Angle USB-C, 3.3 ft / 1 m, silicone, the USB 20Gbps version. Other angled cables may not fit. The cable is not included.
    See the LEIRUI Down Angle USB-C cable on Amazon (paid link)

    Paid link. I earn a commission if you buy through it. As an Amazon Associate I earn from qualifying purchases.

    On Amazon, check that Size shows 3.3 FT / 1 m Silicon and Style shows USB 20Gbps. That is the only version I have tested. The cable is made and sold by another company, so it can change or sell out. If it looks different or is gone, email oleg@olegkovalov.com, or print the version without charging and use a USB-C cable you already own.

  • A certified USB-C charger with a free USB-C port for each cable.
  • Pocket Cam Organizer: your DJI Osmo Pocket 3 or Osmo Pocket 4P. All three pockets can charge, so you need one cable for each pocket you want to charge in. Its download also has an optional cord clip for the three cords.
  • Luna Cam Organizer: your Insta360 Luna Ultra with its protective cover on. The left pocket charges. The other two pockets are storage. It has one cord and no cord clip.

In the download: both versions (with charging and without), the hook fit test, the camera fit gauge, the charging test and three numbered slide-in keys that hold the plug down.

Safety note for the charging versions: this is a printed plastic part that you print and assemble yourself. It is not a certified electrical product. Use the exact cable listed, undamaged, with a certified charger. The cable is made and sold by another company. Keep the organizer away from heat and direct sun, for example a hot car or a sunny window. If the plug, the cable or the organizer ever feels hot, unplug it and stop using it.

FAQ

Is this a physical product?

No. It is a digital download of 3D print files. You print the parts yourself. Nothing is shipped.

What printer do I need?

A printer with a bed of 180 x 180 mm or larger prints four of the five parts. The 360 Cam Holder is 199.7 mm wide and needs a bed at least 220 mm wide. I print on a Bambu Lab X1 Carbon in PLA. Each part comes as a Bambu Studio .3mf sliced for that printer and as a plain .stl for any other printer or slicer.

Which pegboard does it fit?

The IKEA SKADIS pegboard. The hook fit test in every download has three fits for boards of different thickness. I have not tested any other pegboard.

What do I need for charging?

One charging cable for each camera that charges. The plug bay is cut for one exact plug, and this is the only cable I have tested: LEIRUI Down Angle USB-C, 3.3 ft / 1 m, silicone, the USB 20Gbps version. Other angled cables may not fit. The cable is not included. You also need a certified USB-C charger with one port for each cable. The full list and the cable link (a paid Amazon link) are above.

What if I do not want charging?

The Pocket Cam and Luna Cam organizers each come with a version without charging in the same download, for the same price. It needs no special cable and nothing else to buy. It has a plain hole in the pocket floor (every pocket in the Pocket Cam Organizer, the left pocket in the Luna Cam Organizer), so you can still feed a USB-C cable you already own through it and plug the camera in by hand. It has no plug bay, no keys and no latches. The Action Cam, Ace Cam and 360 Cam holders have no charging.

Will it fit my camera in a case or a cage?

Each pocket is cut for one setup, listed on the product. Every download has a camera fit gauge, a short test print that tells you before the long print.

Can I sell prints or share the files?

No. The license is personal: print as many as you need for yourself and as gifts. Do not share, resell or re-upload the files, and do not sell prints without a commercial license. Email oleg@olegkovalov.com to ask for one. Read the full license.

Can I get a refund?

Digital files are delivered instantly, so all sales are final once you download. If a file is faulty or not as described, email me at oleg@olegkovalov.com within 14 days of purchase and I will fix it or refund you. Print the small test pieces in the download first, before any full part. Full refund policy

Not affiliated with IKEA, DJI, Insta360 or LEIRUI. Brand and product names belong to their owners and are used only to describe fit.

Designed by Oleg Kovalov, Video Hook LLC, Fort Wayne, Indiana. Checkout, payment and tax are handled by Lemon Squeezy, the merchant of record. Tax, where it applies, is added at checkout.

Digital download. No physical item is shipped. Cables, chargers, pegboards and cameras are not included.